{
    "schemaVersion": "ooitech-article.v1",
    "url": "https://www.ooitech.com/uvid-in-topcon-solar-cells-non-contact-iv-testing-tracks-passivation-degradation-and-6-72-efficiency-loss.html",
    "language": "en",
    "title": "UVID in TOPCon Solar Cells: Non-Contact IV Tes··· | Ooitech",
    "description": "A study on UV induced degradation (UVID) in TOPCon solar cells using non-contact IV testing, ToF-SIMS and depth-profiling XPS to reveal hydrogen and oxygen dual mechanisms behind 6.72% efficiency loss.",
    "keywords": "TOPCon UVID, UV induced degradation, non-contact IV tester, Al2O3 SiNx passivation, N-H bond breaking, oxygen vacancy, TOPCon solar cell reliability, ToF-SIMS XPS analysis",
    "ogType": "website",
    "image": "https://cdn.ooitech.com/static/upload/image/20260417/2026041717613713.webp",
    "headings": [
        {
            "level": 1,
            "text": "UVID in TOPCon Solar Cells: Non-Contact IV Testing Tracks Passivation Degradation and 6.72% Efficiency Loss"
        },
        {
            "level": 3,
            "text": "UVID in TOPCon Solar Cells: Non-Contact IV Testing Tracks Passivation Degradation and 6.72% Efficiency Loss"
        },
        {
            "level": 5,
            "text": "Introduction"
        },
        {
            "level": 5,
            "text": "Experimental Method"
        },
        {
            "level": 5,
            "text": "Front vs Rear Structure: UV Resistance Compared"
        },
        {
            "level": 5,
            "text": "Chemical Composition Evolution"
        },
        {
            "level": 5,
            "text": "Electrical Performance Degradation"
        },
        {
            "level": 5,
            "text": "Conclusion"
        },
        {
            "level": 5,
            "text": "Ooitech's View"
        },
        {
            "level": 5,
            "text": "Tags :"
        },
        {
            "level": 5,
            "text": "Table of Contents"
        },
        {
            "level": 5,
            "text": "Category"
        },
        {
            "level": 5,
            "text": "Related Posts"
        },
        {
            "level": 6,
            "text": "How a Tabber & Stringer Works — and How to Choose One in 2026"
        },
        {
            "level": 6,
            "text": "TOPCon Solar Cell Manufacturing Process: A Complete Step-by-Step Guide"
        },
        {
            "level": 6,
            "text": "Triple-Junction GaAs Solar Cells: A Detailed Look at the Mainstream Space Photovoltaic Structure"
        },
        {
            "level": 6,
            "text": "33.25% Efficiency, 96% MPPT Retention After 1000 Hours: All-ALD SnOx/AZO Bilayer Suppresses Interface Reactions in Perovskite/Silicon Tandems"
        },
        {
            "level": 6,
            "text": "26.2% Certified Efficiency Breakthrough in Large-Area All-Perovskite Tandem Modules: The In₂O₃ Nanocrystal Tunnel Recombination Junction"
        },
        {
            "level": 5,
            "text": "Recent Post"
        },
        {
            "level": 6,
            "text": "BC-TOPCon's Last Backside Battle: Keep the Bottom SiOx Frozen, Zone the Middle Layer with AlOx/SiOx"
        },
        {
            "level": 6,
            "text": "UVID in TOPCon Solar Cells: Non-Contact IV Testing Tracks Passivation Degradation and 6.72% Efficiency Loss"
        },
        {
            "level": 6,
            "text": "Steel Plate Printing + Local Poly-Silicon Finger: TOPCon's Next Move Is Already Happening"
        },
        {
            "level": 5,
            "text": "Popular Tags"
        },
        {
            "level": 3,
            "text": "Request A Quote"
        },
        {
            "level": 2,
            "text": "We deliver expertise you can trust our service"
        },
        {
            "level": 3,
            "text": "Cost-Effective Advantages"
        },
        {
            "level": 3,
            "text": "Our Experience Team"
        },
        {
            "level": 3,
            "text": "15+ Years Industry Experience"
        },
        {
            "level": 2,
            "text": "What Our Client Say's about us"
        },
        {
            "level": 3,
            "text": "Jizzakh Polytechnic Institute"
        },
        {
            "level": 3,
            "text": "Amjad"
        },
        {
            "level": 3,
            "text": "Mark"
        },
        {
            "level": 3,
            "text": "KTECH"
        },
        {
            "level": 3,
            "text": "Diarra From Africa"
        },
        {
            "level": 2,
            "text": "Our Latest Products"
        },
        {
            "level": 3,
            "text": "Offline String EL Tester OPT-S110H - Solar Cell String Electroluminescence Testing Equipment | Ooitech"
        },
        {
            "level": 3,
            "text": "OSLB-1300 Back Contact Cell Welding Machine | BC Solar Cell Stringer for IBC ABC HPBC Panel Production"
        },
        {
            "level": 3,
            "text": "BD03 Frame Gluing Machine – Aluminum Frame Sealant System"
        },
        {
            "level": 3,
            "text": "Photovoltaic Ribbon Wire Drawing and Tinning Integrated Production Line"
        },
        {
            "level": 3,
            "text": "Solar Panel Testing Equipment for IEC Certification | Complete PV Module Test Solutions by Ooitech"
        },
        {
            "level": 3,
            "text": "SS-2500B Full Automatic Solar Cell Tabber Stringer Machine - High-Speed Production Line Equipment"
        }
    ],
    "wordCount": 1972,
    "markdown": "# UVID in TOPCon Solar Cells: Non-Contact IV Tes··· | Ooitech\n\n> A study on UV induced degradation (UVID) in TOPCon solar cells using non-contact IV testing, ToF-SIMS and depth-profiling XPS to reveal hydrogen and oxygen dual mechanisms behind 6.72% efficiency loss.\n\n![UVID in TOPCon Solar Cells: Non-Contact IV Testing Tracks Passivation Degradation and 6.72% Efficiency Loss](https://cdn.ooitech.com/static/upload/image/20260804/17aeb9818f648b0a8226d34423b2a293.webp)\n\n- ** 2026-08-04\n- ** 0 Views\n- ** [Blog](/Blog.html)\n\n### UVID in TOPCon Solar Cells: Non-Contact IV Testing Tracks Passivation Degradation and 6.72% Efficiency Loss\n\n##### Introduction\n\nTOPCon solar cells now dominate the PV market thanks to strong surface passivation and carrier-selective contacts. But outdoor operation exposes a real weak spot: UV induced degradation, or UVID. After UV60 irradiation, efficiency drops by as much as 6.72%.\n\nMost earlier work blamed UVID on high-energy photons breaking Si–H bonds and releasing free hydrogen. That is only part of the story. The solar UV spectrum spans a wide 3.1–4.43 eV energy range, so its interaction with the front-surface layers goes well beyond a single Si–H rupture pathway. And the front Al₂O₃ / SiNₓ stack is far weaker against UV than the rear side.\n\nA non-contact IV tester helps a lot here. It is non-destructive, uses zero consumables, runs at millisecond speed, works with BC and busbar-free designs, and pulls IV, EQE and PL parameters in a single shot.\n\nThis study uses ToF-SIMS and depth-profiling XPS to track element distribution and chemical bond changes in the Al₂O₃ / SiNₓ layers before and after UV60. The finding: N–H bond breaking is a second hydrogen source alongside Si–H. Al–O bonds in amorphous Al₂O₃ get broken by UV and generate a large number of oxygen vacancies. The hydrogen and oxygen mechanisms stack up and worsen surface recombination, giving a clear direction for improving passivation reliability.\n\n##### Experimental Method\n\n(a) TOPCon solar cell structure schematic (b) symmetric front-structure sample (c) symmetric rear-structure sample\n\nSymmetric front-structure samples (SiNₓ/Al₂O₃/n-Si/Al₂O₃/SiNₓ) and symmetric rear-structure samples (with SiOₓ/n⁺-poly-Si layer) were prepared. UV aging was carried out at module level. The light source was mainly UV-A with about 11% UV-B, under 60°C and 30% humidity.\n\nSpectral irradiance of the UV light source\n\n##### Front vs Rear Structure: UV Resistance Compared\n\nChanges in (a) τeff at an injection carrier concentration of 1×10¹⁵ cm⁻³, (b) iVoc, and (c) single-side J₀ for symmetric front- and rear-structure samples during UV exposure\n\nThe symmetric rear structure barely degraded after 60 kWh·m⁻² of UV exposure. Its 120 nm thick poly-Si layer absorbs almost all the UV light and provides effective shielding.\n\nThe front structure told a different story. τeff dropped from 2895.6 μs to 1552.8 μs. iVoc fell from 735.5 mV to 715.2 mV. Single-side J₀ shot up to 18.4 fA·cm⁻², roughly three times the initial value. The Al₂O₃ / SiNₓ passivation degraded heavily.\n\n##### Chemical Composition Evolution\n\nIntensity depth profiles of (a) hydrogen and (b) oxygen in the polished symmetric front-structure sample before and after UV60, measured by ToF-SIMS\n\nToF-SIMS shows hydrogen concentration rising clearly after UV exposure, especially inside the SiNₓ layer. N 1s XPS depth profiling shows that at the SiNₓ / Al₂O₃ interface, the N–H bond fraction fell from 9.64% to 5.97%. So N–H bond breaking is the second hydrogen source beyond Si–H. The freed hydrogen diffuses toward the SiNₓ surface region and recombines with silicon there, which is why the N–H fraction actually rises near that surface.\n\nOxygen tells an equally important story. Oxygen in the Al₂O₃ layer dropped slightly, while oxygen at the SiNₓ/Al₂O₃ and Al₂O₃/Si interfaces increased. This points to Al–O bonds breaking and free oxygen migrating outward. Al–O bond energy in an ideal crystal is about 5.3 eV. But in amorphous Al₂O₃, under-coordinated aluminum ions and oxygen vacancies trap electrons and turn negatively charged, dropping the activation energy for adjacent Al–O bond rupture to about 2.4 eV. That means 400 nm UV light (3.1 eV) is enough to break them.\n\nN 1s depth-profiling XPS spectra at different interfaces of the Al₂O₃/SiNₓ layer before and after UV60, with fitted curves for N–Si (397.5 eV) and N–H (399.5 eV) bonds\n\nO 1s XPS shows lattice oxygen (OI) converting into oxygen vacancies (OII). In the Al 2p spectra, the Al₂O₃ fraction fell from 69.99% to 60.36% while Al–OH rose from 30.01% to 39.64%. In the Si 2p spectra, Si²⁺ increased while higher-valence silicon dropped. The electrons released when oxygen vacancies form reduce silicon from higher oxidation states. Taken together, these changes in oxygen, aluminum and silicon bonding show the Al₂O₃ film quality has already suffered.\n\n##### Electrical Performance Degradation\n\nEQE and reflectance curves of the TOPCon solar cell before and after UV60\n\nChange in front contact resistivity of the TOPCon solar cell during UV60 exposure\n\nReflectance stayed basically unchanged after UV60. EQE showed a moderate drop in the short-wavelength region below 500 nm, matching stronger front-surface recombination. Front contact resistivity climbed nearly linearly with UV dose, reaching 4.1 mΩ·cm², about 8.6 times higher. The cause: free hydrogen and oxygen generated in the passivation layer diffuse to the electrode interface and take part in redox reactions. UV also converts water molecules on the silver surface into hydroxyl radicals, and together they corrode the metal electrode.\n\nElectrical performance degradation rates during UV60 exposure: (a) Voc (b) Jsc (c) FF (d) Eff\n\nVoc dropped 3.46% relative, driven by front-surface passivation degradation and rising J₀. FF fell 2.82%, driven by higher front contact resistivity. Jsc only dropped 0.64%, since the short-wavelength EQE loss was limited. The final photoelectric conversion efficiency loss came to 6.72%.\n\n##### Conclusion\n\nThe front SiNₓ/Al₂O₃ structure of TOPCon cells is far weaker against UV than the rear structure. Under UV, Si–H and N–H bonds break in sequence and release free hydrogen. Al–O bonds in amorphous Al₂O₃ break under UV, releasing free oxygen and creating a large number of oxygen vacancies. Al₂O₃ converts toward Al–OH and silicon valence shifts. These two degradation mechanisms, hydrogen and oxygen, stack up and worsen surface recombination. Add the sharp rise in front contact resistivity, and the result is 6.72% efficiency loss. The work offers a useful reference for understanding TOPCon UVID and for improving the long-term reliability of passivation layers.\n\n##### Ooitech's View\n\nUVID keeps proving that the front stack is where reliability really gets tested, so how you build and control the SiNₓ/Al₂O₃ deposition and encapsulation on a module line matters just as much as the cell recipe. On our turnkey TOPCon and PERC module lines we see the same lesson play out on the layup, lamination and EL side, small process choices decide whether panels hold up outdoors for years. If you want more hands-on views from the factory floor, the Ooitech YouTube channel at [www.youtube.com/ooitech](http://www.youtube.com/ooitech) is worth a follow.\n\n---\n\n##### Tags :\n\n\n![](/template/ooitech/assets/img/shape/06.png)\n\n![](https://cdn.ooitech.com/runtime/image/w800_h700_fitblur_v2_w800_h700_fitblur_v2_1757399770541443.webp)\n\n### Request A Quote\n\nAll uploads are secure and confidential.\n\n## We deliver expertise you can trust our service\n\nDirect-from-Factory Equipment.\n\n![](/template/ooitech/assets/img/icon/money-2.svg)\n\n### Cost-Effective Advantages\n\nWe deliver exceptional value, maximizing results while optimizing budgets for clients.\n\n![](/template/ooitech/assets/img/icon/staff.svg)\n\n### Our Experience Team\n\nOur skilled professionals specialize in innovative solutions and tailored strategies.\n\n![](/template/ooitech/assets/img/icon/certified.svg)\n\n### 15+ Years Industry Experience\n\nDeep expertise ensures reliable, trend-aware, and proven outcomes for success.\n\n![](https://cdn.ooitech.com/static/upload/image/20250910/1757477357667605.webp )\n\n![](https://cdn.ooitech.com/static/upload/image/20250910/1757477724911512.webp)\n\n![](/template/ooitech/assets/img/shape/06.png)\n\n## What Our Client Say's about us\n\nClient testimonials praise our deep understanding of their challenges, which leads to innovative solutions and strong ROI. Long-term collaborations—some over a decade—demonstrate their trust and satisfaction. Their success stories drive us to continually exceed expectations. [Know More **](#quote-form)\n\n![](/template/ooitech/assets/img/icon/quote.svg)\n\nA man with a big soul. Thank you very much for your visit Mr Wu. Thank you very much for the services provided in installing equipment and training my students. The kindest person and professional in his field\n\n![](https://cdn.ooitech.com/runtime/image/w800_h600_fitblur_v2_2026041716444445.webp)\n\n### Jizzakh Polytechnic Institute\n\n![](/template/ooitech/assets/img/icon/quote.svg)\n\nThanks to Ooitech for providing the fully automated production equipment—your installation and after-sales service have been excellent.\n\n![](https://cdn.ooitech.com/runtime/image/w800_h600_fitblur_v2_2026041720921238.webp)\n\n### Amjad\n\n![](/template/ooitech/assets/img/icon/quote.svg)\n\nThank you again so much again for the very big big help for improving and fixing the factory and also teaching the workers how to use the machines\n\n![](https://cdn.ooitech.com/runtime/image/w800_h600_fitblur_v2_1757479675272137.webp)\n\n### Mark\n\nBIPV Philippines\n\n![](/template/ooitech/assets/img/icon/quote.svg)\n\nThanks to Ooitech for providing highly suitable BC solar cell experimental equipment.\n\n![](https://cdn.ooitech.com/runtime/image/w800_h600_fitblur_v2_1776426122864564.webp)\n\n### KTECH\n\n![](/template/ooitech/assets/img/icon/quote.svg)\n\nthank you for ooitech's professional support and on time after service.\n\n![](https://cdn.ooitech.com/runtime/image/w800_h600_fitblur_v2_1784509010217979.webp)\n\n### Diarra From Africa\n\n## Our Latest Products\n\n![Offline String EL Tester OPT-S110H - Solar Cell String Electroluminescence Testing Equipment | Ooitech](https://cdn.ooitech.com/runtime/image/w800_h600_fitblur_v2_1774350940561245.webp)\n\n- [** Rachael](/offline-string-el-tester-opt-s110h-solar-cell-string-electroluminescence-testing-equipment-ooitech.html)\n- [** 88027](/offline-string-el-tester-opt-s110h-solar-cell-string-electroluminescence-testing-equipment-ooitech.html)\n\n### Offline String EL Tester OPT-S110H - Solar Cell String Electroluminescence Testing Equipment | Ooitech\n\nOPT-S110H Offline String EL Tester from Ooitech delivers high-speed electroluminescence inspection for solar cell strings up to 1250mm. Equipped with 4.6MP dual NIR cameras, electronic shutter, and intelligent defect detection software, it identifies hidd\n\n![OSLB-1300 Back Contact Cell Welding Machine | BC Solar Cell Stringer for IBC ABC HPBC Panel Production](https://cdn.ooitech.com/runtime/image/w800_h600_fitblur_v2_2026032311945973.png)\n\n- [** ooitech](/oslb-1300-back-contact-cell-welding-machine-bc-solar-cell-stringer-for-ibc-abc-hpbc-panel-production.html)\n- [** 98719](/oslb-1300-back-contact-cell-welding-machine-bc-solar-cell-stringer-for-ibc-abc-hpbc-panel-production.html)\n\n### OSLB-1300 Back Contact Cell Welding Machine | BC Solar Cell Stringer for IBC ABC HPBC Panel Production\n\nOSLB-1300 back contact cell welding machine by Ooitech delivers ≥1000 cells/hour throughput for BC, IBC, ABC, and HPBC solar cell string welding. Features A/B dual cell loading, CCD + SCARA robot positioning (±0.2mm), infrared heating welding, inline EL i\n\n![BD03 Frame Gluing Machine – Aluminum Frame Sealant System](https://cdn.ooitech.com/runtime/image/w800_h600_fitblur_v2_1774506308732524.webp)\n\n- [** Rachael](/Offline-Frame-Gluing-Machine-BD03-Professional-Aluminum-Frame-Sealant-Application-System.html)\n- [** 51596](/Offline-Frame-Gluing-Machine-BD03-Professional-Aluminum-Frame-Sealant-Application-System.html)\n\n### BD03 Frame Gluing Machine – Aluminum Frame Sealant System\n\nBD03 CNC frame gluing machine – automated aluminum frame sealant application with precise positioning, automatic feeding and uniform glue distribution for solar panel production lines.\n\n![Photovoltaic Ribbon Wire Drawing and Tinning Integrated Production Line](https://cdn.ooitech.com/runtime/image/w800_h600_fitblur_v2_2026051111285937.webp)\n\n- [** ooitech](/photovoltaic-ribbon-wire-drawing-and-tinning-integrated-production-line.html)\n- [** 429](/photovoltaic-ribbon-wire-drawing-and-tinning-integrated-production-line.html)\n\n### Photovoltaic Ribbon Wire Drawing and Tinning Integrated Production Line\n\nProfessional photovoltaic ribbon wire drawing and tinning integrated production line for round and flat solar ribbon manufacturing with high-speed 450M/min capacity and automatic servo control system\n\n![Solar Panel Testing Equipment for IEC Certification | Complete PV Module Test Solutions by Ooitech](https://cdn.ooitech.com/runtime/image/w800_h600_fitblur_v2_2026032716200590.webp)\n\n- [** Rachael](/solar-panel-testing-equipment-for-iec-certification-complete-pv-module-test-solutions-by-ooitech.html)\n- [** 92190](/solar-panel-testing-equipment-for-iec-certification-complete-pv-module-test-solutions-by-ooitech.html)\n\n### Solar Panel Testing Equipment for IEC Certification | Complete PV Module Test Solutions by Ooitech\n\nOoitech offers a complete range of solar panel testing equipment for IEC61215 and IEC61730 certification, including visual inspection stations, wet leakage testers, steady state simulators, UV aging chambers, damp heat test chambers, mechanical load teste\n\n![SS-2500B Full Automatic Solar Cell Tabber Stringer Machine - High-Speed Production Line Equipment](https://cdn.ooitech.com/runtime/image/w800_h600_fitblur_v2_1774258018905303.webp)\n\n- [** ooitech](/SS-2500B-Full-Automatic-Solar-Cell-Tabber-Stringer-Machine-High-Speed-Production-Line-Equipment.html)\n- [** 36663](/SS-2500B-Full-Automatic-Solar-Cell-Tabber-Stringer-Machine-High-Speed-Production-Line-Equipment.html)\n\n### SS-2500B Full Automatic Solar Cell Tabber Stringer Machine - High-Speed Production Line Equipment\n\nSS-2500B full automatic tabber stringer machine for crystalline silicon solar cells with 2400PCS/H capacity, featuring infrared soldering, robotic handling, CCD inspection, and dual-station simultaneous welding for efficient solar panel production\n",
    "endpoints": {
        "html": "https://www.ooitech.com/uvid-in-topcon-solar-cells-non-contact-iv-testing-tracks-passivation-degradation-and-6-72-efficiency-loss.html",
        "markdown": "https://www.ooitech.com/uvid-in-topcon-solar-cells-non-contact-iv-testing-tracks-passivation-degradation-and-6-72-efficiency-loss.md",
        "agentManifest": "https://www.ooitech.com/.well-known/agent.json",
        "llmsTxt": "https://www.ooitech.com/llms.txt",
        "sitemap": "https://www.ooitech.com/sitemap.xml",
        "quote": "https://m.ooitech.com/api/quote.php"
    }
}